20231103: BCM5751 LinuxをLinuxにいれる¶
$ lspci
03:00.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 21)
ubuntu@optiplex:~$ sudo lshw -c network -businfo
Bus info Device Class Description
=========================================================
pci@0000:01:00.0 enp1s0f0np0 network MT27710 Family [ConnectX-4 Lx]
pci@0000:01:00.1 enp1s0f1np1 network MT27710 Family [ConnectX-4 Lx]
pci@0000:02:00.0 enp2s0 network RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
pci@0000:03:00.0 enp3s0 network NetXtreme BCM5751 Gigabit Ethernet PCI Express
ubuntu@optiplex:~$ sudo ethtool enp3s0
Settings for enp3s0:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Half 1000baseT/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Link partner advertised pause frame use: Symmetric
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
Port: Twisted Pair
PHYAD: 1
Transceiver: internal
MDI-X: on
Supports Wake-on: g
Wake-on: d
Current message level: 0x000000ff (255)
drv probe link timer ifdown ifup rx_err tx_err
Link detected: yes
ubuntu@optiplex:~$ sudo lspci -s 03:00 -vv
03:00.0 Ethernet controller: Broadcom Inc. and subsidiaries NetXtreme BCM5751 Gigabit Ethernet PCI Express (rev 21)
Subsystem: Broadcom Inc. and subsidiaries NetXtreme BCM5751 Gigabit Ethernet PCI Express
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 141
Region 0: Memory at f7210000 (64-bit, non-prefetchable) [size=64K]
Expansion ROM at f7200000 [disabled] [size=64K]
Capabilities: [48] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
Capabilities: [50] Vital Product Data
Product Name: HPQ 10/100/1000 Copper Based Gigabit Adapter
Read-only fields:
[PN] Part number: BCM95751A519
[EC] Engineering changes: 112791-10
[SN] Serial number: 0123456789
[MN] Manufacture ID: 14e4
[RV] Reserved: checksum good, 26 byte(s) reserved
Read/write fields:
[YA] Asset tag: XYZ01234567
[RW] Read-write area: 107 byte(s) free
End
Capabilities: [58] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee00498 Data: 0000
Capabilities: [d0] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <4us, L1 unlimited
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE- FLReset- SlotPowerLimit 10.000W
DevCtl: CorrErr- NonFatalErr- FatalErr- UnsupReq-
RlxdOrd- ExtTag+ PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Exit Latency L0s <2us
ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp-
LnkCtl: ASPM Disabled; RCB 64 bytes, Disabled- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s (ok), Width x1 (ok)
TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Advanced Error Reporting
UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr-
AERCap: First Error Pointer: 14, ECRCGenCap+ ECRCGenEn- ECRCChkCap+ ECRCChkEn-
MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
HeaderLog: 04000001 0000000f 03010000 00000000
Capabilities: [13c v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [160 v1] Device Serial Number 98-b7-85-ff-fe-00-9a-f5
Kernel driver in use: tg3
Kernel modules: tg3
ドライバのインストール(出来なかった)¶
(なにもいらないらしい)
Broadcom NetXtreme-E Niccli Utility - Linuxをいれる。
unzip niccli-227.0.130.0_linux.zip
cd Linux/Linux_x86_64/
sudo dpkg -i *deb
cd ../..
cd Linux/sliff
sudo dpkg -i *deb
sudo apt --fix-broken install
# 色々足りないのでfixします
sudo apt install dkms
niccli
> -------------------------------------------------------------------------------
> Scrutiny NIC CLI v227.0.130.0 - Broadcom Inc. (c) 2023 (Bld-61.52.25.90.16.0)
> -------------------------------------------------------------------------------
> ERROR: Discovery failed. Unable to discover any supported device(s).
sudo ./bnxtnvm list
> なにもでない